โ˜Ž +86 187 5400 6560  ยท  โœ‰ thetiet40@gmail.com

Home / Products / Casters, Glides & Levelers

Component Guide ยท November 2026

Furniture Casters, Glides and Levelers Guide 2026: Load Ratings, Wheel Materials and Specification

๐Ÿ‡จ๐Ÿ‡ณ ้˜…่ฏปไธญๆ–‡็‰ˆ โ†’

A cabinet is judged by its doors and top, but it stands on four small parts that cost less than one handle. When they are wrong, the failure is loud: a caster flat-spots into a thump, a glide scratches a floor, a leveling foot strips its thread and base units lean.

This guide covers the three families that touch the floor: load calculation, wheel and floor pairing, mounting, service failures, and how to write a specification a factory cannot quietly downgrade.

Three families, three different jobs

A caster is a wheel in a swivel or fixed bracket, for furniture that moves regularly: display fixtures, office pedestals, hospital furniture, kitchen islands and trolleys. Its value is mobility; its cost is height, complexity and a load path through a small axle.

A glide is a low, fixed foot that lets a piece slide or protects the floor. It suits chairs, sofa legs, light cabinets and shelving that are positioned once and left alone. A glide is not a wheel; dragging a heavy cabinet on glides is a floor-damage problem waiting to happen.

A leveler is an adjustable foot that compensates for an uneven floor and brings a cabinet to height after installation. It is standard on kitchen units, wardrobes and counters. It carries load but does not roll, and its adjustment range belongs in the specification.

The first mistake is mixing categories: a “caster” that is really a glider will not roll, a “leveler” that is fixed will not adjust, and a decorative foot under a loaded cabinet fails at the stem.

Load rating: the number is per caster

Caster catalogues quote a load per unit, but buyers routinely read it as the load for the set. A cabinet rated at 300 kg on four 75 kg casters is not automatically safe, because the load is rarely shared equally.

Three rules make the calculation honest:

  • Use three wheels, not four. On an uneven floor one wheel can lose contact, so the other three carry the load. Divide the total weight by three.
  • Separate dead and live load. The cabinet and contents are dead load; a person leaning on it, an open drawer or a push adds live load.
  • Apply a working factor. For furniture pushed daily, 1.5 over the calculated wheel load is a sensible start; for heavy industrial or outdoor use, go higher.

A worked example: a 120 kg island with 30 kg of contents weighs 150 kg. Divided by three, that is 50 kg per wheel; with a 1.5 factor, specify at least 75 kg per caster. A 100 kg caster is the better choice for a counter someone may lean on.

Dynamic rating is lower than static: a caster that holds 100 kg standing still may roll at 70โ€“80 kg, and the gap widens with speed, small wheels and rough floors. If the furniture moves daily, ask for the dynamic figure. Check the mounting too: the wheel may be strong while the plate screws or stem socket are not.

Wheel materials and floor compatibility

The wheel is where the caster meets the building. The wrong compound damages floors, makes noise or fails early, and the difference is invisible in a photo.

  • Polypropylene (PP): the low-cost default. Hard and light, but noisy on tile and harsh on wood; best for light storage, utility carts and smooth concrete.
  • Nylon: harder and stronger than PP, with low rolling resistance. It can be noisy and may mark soft floors under a heavy point load; common on industrial casters.
  • Polyurethane (PU): quiet, floor-friendly and abrasion resistant, which is why it dominates office and retail furniture. Cheap PU can hydrolyse in warm, humid storage, and sharp debris can cut the tread.
  • Rubber: soft, quiet and grippy, with higher rolling resistance. Natural rubber can leave black marks on light floors and flat-spot under static load.
  • Thermoplastic rubber (TPR): softer and cheaper than PU, quiet on hard floors, best for light indoor furniture.
  • Steel or cast iron: for very high loads and industrial environments. It damages most finished floors and does not belong in a showroom.

Match the wheel to the floor, not the catalogue photo. Hard wheels on tile transmit noise; soft wheels on carpet feel draggy; black rubber on pale LVT is a complaint waiting to happen. For wood, LVT and polished concrete, specify a non-marking soft PU or suitable TPR and test on an offcut. For carpet, a larger diameter rolls more easily. Outdoors, check UV and water resistance.

Wheel diameter also decides how furniture handles thresholds and grout lines. A 50 mm wheel is fine on a smooth floor; 75โ€“100 mm crosses a 10 mm threshold more easily and rolls with less effort under a loaded trolley.

Bearings, swivel geometry and brakes

Two casters with the same wheel can feel completely different because of the bearing. A plain bearing is a simple sleeve: cheap, tolerant of dirt and adequate for light, occasional movement. A ball bearing reduces starting effort under load but costs more and can be damaged by grit. For furniture moved daily, a ball-bearing swivel is usually worth the difference; for a cabinet that moves twice a year, it is not.

Swivel offset matters as much. The wheel sits behind the swivel axis, and that offset is what makes the caster trail and self-centre. Too little and the caster fights the direction of travel; too much and it shimmies. A double-ball race turns more easily under a heavy cabinet but has more places for dust and water to enter. Load the furniture, push it across the actual floor, turn a full circle and listen.

Brakes are safety parts. A wheel brake locks only the wheel, so the furniture can still swivel. A swivel lock fixes direction, often to make a cart track straight. A total lock holds both wheel and swivel, and is the type for a mobile island or display plinth that must stay put while someone leans on it. Test the brake loaded, on the real floor: one that holds an empty cart may slip when full. For a kitchen island, specify total lock on at least two casters and make sure the pedal is reachable.

Mounting: plate, stem or bolt hole

A caster is only as strong as its connection to the furniture.

Top-plate mounting is the most common for cabinets and trolleys: a plate screwed to the underside with four screws. Plate size and hole spacing must match, and the plate must sit flat. A plate bridging a recess or a warped panel will loosen; for heavy loads, through-bolt it rather than relying on wood screws alone.

Threaded-stem mounting screws into a socket or threaded insert. Common stems are M8, M10 and M12, but socket depth and panel material decide real capacity. A stem in thin particle board can pull out long before the caster reaches its rated load. Reinforce the point or use a through-bolt with an inside plate. Grip-ring stems push into a socket and suit light furniture and office chairs, not heavy cabinets. Bolt-hole mounting passes a bolt through the caster and frame, strong and compact for industrial equipment and custom frames.

For wood screws, engagement length matters more than diameter: 12โ€“15 mm of solid material holds far better than a long screw bottoming out in a void. In particle board, pilot holes and the right thread are essential; over-tightening crushes the board. If a caster is rated above roughly 50 kg and mounts into particle board, design in a metal plate or through-bolt.

Glides and levelers

Glides are simple, which is why they are specified carelessly. A glide has a base, a stem and a floor-contact material.

  • Nylon or PTFE: low friction and hard, for carpet and light furniture. They slide rather than roll.
  • Felt: quiet on wood and LVT, but wears and picks up grit; best for chairs that are lifted, not dragged.
  • Rubber or TPR: grip and protect the floor but make the piece harder to move; good for sofa legs and fixed cabinets.
  • Metal: durable and load-bearing, but hard on floors unless fitted with a plastic or felt pad.

Stems are nail-on, screw-on, snap-on or threaded. Nail-on is fast and cheap but can split a small leg; screw-on holds better in solid wood; threaded allows replacement and height adjustment. For a dining chair, a replaceable screw-in glide is a better service decision than a nail-on pad.

Glides do not adjust. On an uneven floor they rock or leave a gap, which is where a leveler belongs, not a thicker felt pad. Glides also concentrate load on a small contact area and can dent a soft floor; check base diameter, not just stem.

A leveler combines a threaded stem, a base and often a locking nut. Its specification has four numbers: thread size, adjustment range, base diameter and load per foot. Common furniture levelers use M8 or M10 threads with 20โ€“40 mm adjustment and a 30โ€“50 mm base; a typical cabinet foot is rated around 80โ€“150 kg, but the real limit is the insert and panel. Install the insert square, screw the foot in by hand, set the cabinet upright, adjust gradually, then tighten the lock nut. Do not use the foot to jack a twisted carcass straight; it only hides the twist until the first heavy load.

Corrosion, cleaning and failure modes

Casters and levelers live in the dirtiest part of the furniture. Zinc plating is adequate for dry indoor furniture but is not a wet-room finish. Chrome or nickel gives a decorative, wear-resistant surface, but a scratch exposes steel underneath. Stainless steel is the right answer for wet rooms, outdoor furniture and coastal sites, at a higher cost; confirm the grade rather than accepting the word “stainless”. Engineering plastics resist water and most household chemicals, but not every solvent.

Aggressive floor cleaners, bleach and steam attack plating, rubber and PU. A caster that corrodes from the inside out is often a cleaning-chemical problem, not a manufacturing defect. If a project has a defined cleaning regime, put it in the RFQ. Ask for a salt-spray report when corrosion resistance matters; “rust-proof” is marketing, not a specification.

Most complaints fall into a few patterns:

  • Flat spots: a soft wheel stood under load for months. Use a harder or larger wheel, or one that is not loaded when parked.
  • Tread separation: a bonded PU or rubber tread lifts from the core, usually from heat, water or poor bonding; a supplier-quality issue.
  • Axle wear and wobble: dirt, missing washers or a load above the bearing rating. A wobbly wheel eventually binds.
  • Stem pull-out: the socket or panel failed. A clean pull-out means the insert was too small or the panel too thin; a crushed hole means over-tightening.
  • Brake slip: worn pawl, stretched spring or contamination. A brake dragged while engaged will never hold again.
  • Swivel jam: hair, carpet fibre, grit or corrosion in the race. Sealed or capped swivels help in dirty environments.
  • Floor marking: plasticiser from a soft black wheel, or a hard wheel abrading a coating. Match the compound to the floor and test on an offcut.

Each failure points to a different fix. Replacing a failed caster with the same model without asking why it failed usually buys another failure.

RFQ and incoming inspection

A caster RFQ that says “75 mm swivel caster, 100 kg” leaves the factory free to choose bearing, wheel compound, plate thickness and brake. Write the requirement in lines:

  1. Application and furniture type.
  2. Load per caster, with dead and live load separated.
  3. Wheel diameter and overall height.
  4. Wheel material and colour, including non-marking requirement.
  5. Bearing type: plain, ball or roller.
  6. Swivel or fixed, with offset if critical.
  7. Mounting: plate size and hole spacing, or stem thread and length.
  8. Brake type: wheel, swivel or total lock.
  9. Finish and corrosion requirement.
  10. Floor type and cleaning regime.
  11. Test requirement: load, brake, roll and salt spray where relevant.
  12. Packing, labelling and spare parts.

For glides and levelers, replace the wheel lines with base diameter, stem type, thread, adjustment range and load per foot, and add panel material and thickness.

Then inspect five things: dimensions against the approved sample; load a set, leave it standing, then roll it; brake it loaded and push; roll and swivel it on the actual floor, listening for squeaks and marking; and check plating coverage, scratches and thread damage. Keep the approved sample and a short test record; two years later it settles whether specification or production changed.

FAQ

How do I calculate the load rating for furniture casters?

Add the furniture and maximum contents weight, divide by three to allow for one wheel losing contact, then apply a working factor of about 1.5 for daily movement. A 150 kg loaded cabinet therefore needs casters rated at roughly 75 kg each, and 100 kg gives useful margin.

Which caster wheel is best for wood floors?

A soft, non-marking polyurethane or suitable TPR wheel, tested on an offcut of the actual floor. Hard nylon and PP transmit noise and can abrade wood; black rubber can mark. Do not drag a loaded cabinet on glides.

Do I need braked casters on a kitchen island?

Yes, at least two total-lock casters. A wheel brake alone still allows the island to swivel; a total lock holds both wheel and swivel. Test it with the island loaded, on the real floor, and check the pedal is reachable.

What is the difference between a glide and a leveler?

A glide is a fixed foot that slides or protects the floor and does not adjust. A leveler has a threaded stem and adjusts height for an uneven floor. A glide under an uneven cabinet will rock; a leveler is the correct part.

Why do leveling feet pull out of particle board?

The insert or panel is too thin, or the foot was over-tightened and crushed the board. Use a proper threaded insert or T-nut, keep it square, and reinforce heavy mounting points. A foot’s rated load is meaningless if the panel cannot hold it.


Ready to build your next furniture project?

WFMingKun Hardware supplies casters, glides, leveling feet, support legs and cabinet hardware from partner factories in China, with approved samples and OEM/ODM support. MOQ from 500 pcs per item, trial quantities from 50 pcs; samples in 3โ€“7 working days, production 15โ€“30 days after deposit.

Browse our brackets and supports, cabinet hardware or furniture support legs, or send us your inquiry with your load, floor type and mounting details โ€” prices, MOQ and lead time within 24 hours. WhatsApp: +86 187 5400 6560.



Scroll to Top