Bathroom Hardware Guide · October 2026
Bathroom Vanity Hardware Guide 2026: Hinges, Slides and Handles for Wet Rooms
A vanity is the one cabinet in a house that is wet on the outside and damp on the inside. A sink is cut into its top, a waste trap runs through its middle, the mirror above it steams over twice a day, and the cleaning routine is built on chemicals designed to dissolve mineral deposits — including, if you are unlucky, the plating on its handles.
That makes the bathroom the most demanding indoor environment this industry sells into. A kitchen hinge works ten thousand times in twenty years. A vanity hinge works in air that swings between 40% and 95% relative humidity, with condensation forming on cold metal every morning.
This guide covers what has to be specified for a vanity or mirror cabinet: hinge families and their limits, slides that work around a plumbing stack, handles that can be gripped wet, and the dimensional checks that decide whether the order fits. It is written for importers building a bathroom line and for buyers who must defend the specification two years later.
Why the bathroom defeats hardware that works elsewhere
Humidity cycling. Water condenses on any metal cooler than the air — inside a hinge cup, on a slide race, under a handle. Condensation alone rarely destroys a part; condensation plus dust plus one scratch in the plating does. Moisture also enters the board, and a screw that held in a dry panel pulls out of a damp one.
Chemistry. Descalers contain citric, phosphoric or hydrochloric acid; mould removers contain chlorine; cream cleaners are abrasive. Zinc alloy and thin decorative chrome go first: the surface dulls, blisters, then pits. A handle described only as “chrome plated”, with no nickel thickness, has no defence against a weekly acid spray.
Tight tolerances. A vanity sits between a wall, a tiled floor and a stone top, often with a door swinging within 600 mm of the cabinet — no room for a hinge that opens 100° when the drawing assumed 110°.
And nobody inspects a vanity: it is installed, siliconed and forgotten until a door drops or a handle turns green.
Hinges: the door side of a vanity
A two-door vanity needs two concealed hinges per door (three above roughly 900 mm or 10 kg), two slides per drawer, two handles, four levelling feet and often a catch; a mirror cabinet adds glass-door hinges and shelf pins. Each is a separate specification line, and a “bathroom set” is only useful if the supplier states the grade, plating thickness and load rating of every item inside it.
The standard vanity hinge is a 35 mm cup concealed hinge: cup depth 11.5–13 mm, door thickness 16–22 mm, overlay 16–18 mm, opening 110°. That is the commodity specification, available at almost any price. What differs in a bathroom is material and adjustment.
Most hinge bodies are zinc alloy with a steel arm and nickel plating. In a dry kitchen that is fine. In a bathroom the plating is all that stands between the steel and the air: specify nickel at 8–12 µm rather than “nickel plated”, and choose stainless arms and cups for exposed positions — a door next to a shower, or any coastal project.
Hydraulic soft-close dampers are standard, but the damper is a wear item. On a door opened twenty times a day, a cheap one loses its cushion in two or three years and the door starts to slam — exactly the noise a hotel guest complains about. Ask for the damper cycle count, and keep one spare hinge per fifty doors on a project.
The hinge is only as good as the two screws in its plate. Coarse-thread 3.5–4 mm screws hold well in particleboard with a pilot hole; in denser moisture-resistant MDF, a finer thread or a machine screw into a threaded insert is more reliable. Three-way adjustment (side, height, depth) is what lets a fitter close a 3 mm gap without re-drilling; on a stone-topped vanity where the top is fixed before the doors go on, depth adjustment is the difference between a clean reveal and a return visit.
Mirror cabinet and glass doors
A mirror cabinet adds a second hinge family, and the two approaches are not interchangeable.
Clamp-on glass hinges grip the glass edge with a screw clamp, no drilling. They suit 4–6 mm glass and are the practical choice for mirror doors, where drilling risks cracking the silvering. The clamp needs a rubber or nylon gasket so glass never bears on metal, and the hinge must be rated for the actual thickness — a 5 mm clamp on 4 mm glass will not hold adjustment.
Screw-fixed glass hinges use a drilled hole and gasket, give a more rigid fixing, and are common on frameless mirror doors above 600 mm.
Weight decides how many hinges. Glass is roughly 2.5 kg per square metre per millimetre, so a 600 × 700 mm door in 4 mm mirror weighs about 4.2 kg, and about 6.3 kg in 6 mm. Two hinges handle most doors up to 600 mm and 8 kg; above that use three. Mirror doors also need a catch or magnetic stay, and a soft-close damper if the cabinet sits above a basin — a slammed mirror door is a cracked mirror waiting to happen.
One detail gets missed: mirror doors are often 4 mm mirror bonded to a 16 mm board. The panel is heavier and stiffer than glass alone, so specify the hinge for the bonded assembly. If the edge is exposed, seal or paint it so moisture cannot creep behind the silvering.
Drawer slides: the plumbing is the constraint
A vanity drawer is an ordinary drawer until it meets the waste trap. Under a basin, the centre of the cabinet is occupied by a 32–40 mm trap, two supply lines and a shut-off valve, and the usable depth shrinks from the back. Most vanity projects go wrong here, and the decision is made at the drawing stage, not at the hardware order.
Measure the obstruction first: the trap footprint in plan, its height above the cabinet floor, and the supply line positions. A typical trap occupies about 200 × 300 mm behind the drawer back, but only the on-site number matters.
Then choose the drawer form. Three options work: a shallow top drawer in front of the trap (80–120 mm internal height, for toothbrushes and small bottles); a notched or U-shaped box built around the trap, the usual factory solution for the main storage drawer; or a false front over the trap with storage either side — cheapest, and honest, provided the front is fixed so it cannot be pulled off.
Slides. Undermount soft-close slides are the default: hidden mechanism, 3D front adjustment, full extension so the back of the drawer is reachable. They need 12.7 mm clearance each side plus clearance under the box, and the box must be built to the slide’s dimensions. Side-mount ball-bearing slides are cheaper and easier to retrofit but offer less adjustment. Push-to-open is best avoided: wet hands mark the front and the latch gums.
Length and load. A 500 mm deep vanity takes a 450 mm slide: measure from the back of the closed front to the obstruction and subtract 10 mm. 25–35 kg per pair is the normal class and enough — a drawer of shampoo bottles rarely exceeds 15 kg. The weak point is the box bottom and front fixings, not the slide.
Corrosion inside the cabinet. The slide is the part nobody sees and the part that rusts first. Thinly passivated zinc-plated steel shows white rust on the race within a season. Specify galvanised or stainless slides, or at minimum a zinc-flake or painted coating with grease that does not emulsify.
Handles and knobs: grip, projection and placement
Handles are chosen for appearance and bought for feel, and in a bathroom both matter more than in a kitchen.
Projection. Counters usually overhang the door by 20–30 mm, and a pull projecting 25 mm leaves no room for fingers. Specify 30–35 mm as a minimum and 40 mm on deep drawers or thick stone tops — or use an edge pull that projects nothing, the best answer on small vanities where a bar would hit the wall.
Section and size. A round or oval bar is comfortable wet; a square edge is not, and polished chrome is the most slippery finish when wet. Standard hole pitches are 96, 128, 160 and 192 mm: decide the pitch before the doors are drilled, and make sure the drill jig matches. On a 400 mm drawer front a 160 mm pull looks right; 96 mm looks mean and 192 mm leaves too little margin.
Placement. On doors, put the knob opposite the hinge, 40–60 mm in from the edge, aligned with the top rail or centred on the stile. On drawers, centre horizontally and vertically. On a mirror cabinet, use a small knob or edge pull — a long bar will hit the wall or the adjacent mirror.
Material. 304 stainless or solid brass for exposed positions. Zinc die-cast with good plating is acceptable in a gently cleaned guest bathroom and wrong for a family bathroom where descaler is used weekly. Aluminium is soft: it dents at the fixings.
Corrosion: what “bathroom grade” should mean
“Bathroom grade” is marketing, not a standard. In a specification it should mean four things: a named stainless grade for exposed parts (304 baseline, 316 for coastal or commercial); a stated plating system with thicknesses, for example copper 8 µm / nickel 10 µm / chrome 0.2 µm; a salt-spray result with method, duration and acceptance criterion — neutral salt spray per ISO 9227, 72 hours for exposed bathroom fittings, no red rust or blistering; and sealed cut edges with stainless fasteners throughout.
Salt spray is accelerated, not a service-life prediction: a part surviving 72 hours is simply better than one that fails at 24.
The most common corrosion failure in a vanity is not the handle but the screw: a stainless handle fixed with a zinc-plated screw shows a rust bloom within a year, and the customer blames the handle. Specify A2 stainless screws for every exposed fixing.
Finishes that survive bathroom cleaning
- Chrome over nickel over brass or zinc. The default, and good when the nickel layer is thick enough. Acid descalers attack chrome at scratches; never leave descaling gel on a chrome fitting.
- PVD. A thin, very hard coating — titanium nitride for gold, zirconium-based for black and brushed tones. Colour-stable and more scratch-resistant than paint, but thin, so the substrate still has to resist corrosion.
- Powder coating on aluminium. 40–60 µm interior, 60–80 µm wet or exterior. Durable, but chips at edges, and a chip in a bathroom is where corrosion starts.
- Matte black. Check whether it is PVD or paint. Paint over zinc in a wet room fails at the edges within a couple of years; PVD does not.
Every finish benefits from a written care line: pH-neutral cleaner, no abrasive, dry the fitting after cleaning. That single sentence prevents a large share of warranty claims.
Dimensions, fits and the RFQ checklist
- Vanity height: 800–850 mm to the top of the counter; 850 mm suits taller users and wall-hung units.
- Counter overhang: 20–30 mm beyond the door face — check it against handle projection.
- Door gap: 2–3 mm at the cabinet edge, consistent top to bottom.
- Service access: a removable back panel or cut-out for the trap. A vanity that must be unscrewed from the wall to fix a leak is a design fault.
- Door swing: a 110° hinge needs clear space beside the cabinet; within 600 mm of a side wall, use a 165° hinge.
For each model, the RFQ should state: door material, thickness and weight; hinge type, cup, angle, finish and stainless grade; mirror cabinet glass thickness, door size, hinge family and catch; drawer box type and internal dimensions, slide family, length, load class and motion; trap footprint and drawer form; handle material, finish, projection, pitch and screw grade; the salt-spray requirement; and a signed golden sample including screws.
Installation and handover checks
Set the cabinet level and plumb before the top goes on, and adjust the feet so the doors hang square. Seal the joints with neutral-cure silicone, not acetic — the acid in standard silicone attacks plated and zinc surfaces and etches stone. Keep silicone off hinges and slides; a slide with silicone in the race is scrap.
At handover, open and close every door and drawer ten times, check the reveal with a 2 mm gauge, confirm the soft-close engages in the last 30°, and confirm the trap is accessible. Then hand over the care instruction — two minutes of checking prevents most complaints.
FAQ
Do I need stainless hinges in a bathroom?
For exposed hinges, coastal sites or hotels, yes — 304 stainless is the reliable choice. In a ventilated guest bathroom a well-plated zinc hinge with 10 µm nickel can last, but if the specification does not name the plating thickness, assume the cheapest.
Can I use standard kitchen drawer slides under a vanity?
Yes, if they clear the trap and the cabinet is ventilated. The constraint is mechanical: the trap and supply lines limit drawer depth, and an over-long slide fouls the plumbing. Choose a slide about 50 mm shorter than the clear depth behind the drawer front.
How do I fit a drawer around a sink trap?
Measure the trap footprint and height, then pick one of three forms: a shallow drawer in front of it, a notched or U-shaped box around it, or a false front with storage either side. The notched box is the standard factory solution.
What is the best finish for bathroom cabinet handles?
Satin or brushed stainless, PVD, or powder-coated aluminium are the most forgiving in daily use. Polished chrome looks right but is slippery when wet. Matte black is excellent if it is PVD; painted black over zinc is not a bathroom finish.
How many hinges does a mirror cabinet door need?
Two for doors up to about 600 mm wide and 8 kg; three above that, or for doors taller than 900 mm. Mirror doors are heavier than they look — 6 mm glass is about 15 kg per square metre — so the hinge must be rated for the glass thickness and the bonded panel.
Ready to build your next vanity project?
WFMingKun Hardware supplies cabinet and furniture hardware — hinges, slides, handles, connectors, brackets and fasteners — factory-sourced from partner factories in China, with approved samples, OEM/ODM support and export documentation for distributors, importers and joinery contractors. MOQ from 500 pcs per item, trial quantities from 50 pcs on most items; samples in 3–7 working days, production 15–30 days after deposit.
Browse our cabinet hardware range, hinges or drawer slides, or send us your inquiry with your vanity hardware list and finish — prices, MOQ and lead time within 24 hours. Prefer to talk first? WhatsApp: +86 187 5400 6560.

