☎ +86 187 5400 6560  ·  ✉ thetiet40@gmail.com

Home / Products / Hinge Overlay & Angle

Industry Insights · October 2026

Hinge Overlay & Angle Guide 2026: Full Overlay, Half Overlay and Inset Math

🇨🇳 阅读中文版 →

Most hinge complaints are geometry, not quality. The door rubs the carcass because the overlay was never calculated; the gap looks uneven because the base plate height changed between batches; the drawer front clips the door because the opening angle was chosen from a catalogue photo. A hinge is a mechanism with three numbers that have to agree: the cup position on the door, the plate position on the carcass, and the angle the door needs to swing.

This guide works through the three mounting types, the angle families, the boring dimensions that matter, and the arithmetic that keeps doors aligned.

The three mounting types

Every cabinet hinge answers one question first: where does the door sit relative to the carcass side?

  • Full overlay. The door covers the entire carcass edge. This is the standard for frameless (full-access) cabinets and the most common specification in European-style kitchens. One door per opening side, with the hinge cranked to bring the door face flush over the panel edge.
  • Half overlay (twin/double). Two doors share one carcass partition, each covering half of it. Used where two doors meet on a single vertical divider — common in wardrobes and wide base cabinets.
  • Inset. The door sits inside the cabinet opening, flush with the carcass face. The most furniture-like look and the least forgiving: every gap is visible, so the carcass, the door and the hinge all have to be accurate.

The mounting type decides the hinge crank (the bend in the arm), not the cup. A full-overlay hinge cannot be made to work as an inset hinge by adjusting screws, however much travel the adjustment offers.

Angles: what the number actually changes

The angle in a hinge name is the opening angle — how far the door swings from closed. It is not a quality grade.

  • 100–110 degrees — the everyday cabinet hinge. Enough to reach into a base unit; the standard for doors that do not sit next to a wall or an appliance.
  • 125–135 degrees — more clearance for wide doors and corner situations.
  • 155–175 degrees — for doors that must fold back against an adjacent panel: corner cabinets, appliance garages, doors beside a return wall.

Two practical consequences:

  1. A wider angle needs more room behind the door. A 165-degree hinge swings the door further back; if a handle or a neighbouring panel is in the arc, the door will hit it before reaching the angle.
  2. The angle affects the crank, and the crank affects the overlay range. When you change the angle, re-check the overlay, not just the swing.

Cup boring: the dimensions that decide everything

The cup is the part of the hinge that sits in the door. Standard dimensions for European-style concealed hinges:

  • Cup diameter — 35 mm is the universal standard; 26 mm exists for narrow aluminium frames.
  • Cup depth — typically 11.5–13 mm, which sets the minimum door thickness (16 mm practical minimum, 18 mm comfortable).
  • Cup distance from the door edge (K) — the distance from the door edge to the near edge of the cup bore. 3–5 mm is the normal range; this number, not the hinge, sets the maximum overlay.
  • Bore centre from the door edge — cup distance plus half the cup diameter. With a 35 mm cup and K = 5 mm, the centre sits 22.5 mm from the edge.

Work from the boring pattern, not from the hinge’s marketing sheet. A hinge can only deliver the overlay its crank allows at the cup distance you have actually bored.

The overlay calculation

Overlay is how much of the carcass edge the door covers. The working relationship is:

Overlay = (door width covered by hinge geometry) — (carcass side thickness) x (mounting factor)

In practice, hinge manufacturers publish an overlay table for each hinge: a matrix of cup distance against base plate height, giving the overlay achieved. Use the table, then verify with arithmetic:

Overlay = half door width — (carcass thickness / 2) — door gap — hinge crank offset

A simpler way to think about it, which catches most errors:

  1. Decide the reveal you want at the carcass edge (full overlay = 0 mm reveal, half overlay = half the panel thickness, inset = door thickness set back).
  2. Pick the base plate height that produces that reveal at your cup distance, using the manufacturer’s table.
  3. Check the adjustment range: a 2 mm plate with ±2 mm cam adjustment covers 0–4 mm of overlay, so anything outside that needs a different plate, not a screwdriver.

Worked example: a full-overlay base cabinet

Assume an 18 mm carcass, a 19 mm door, a 35 mm cup at K = 5 mm, and a hinge whose published table gives 17 mm overlay with a 0 mm plate and 19 mm with a 2 mm plate.

  • Required overlay: the door must cover the full 18 mm carcass edge, plus the 2 mm door gap at the meeting stile. Target overlay ≈ 18 mm.
  • At K = 5 mm, the 0 mm plate gives 17 mm — 1 mm short, which shows as a visible sliver of carcass at the edge.
  • The 2 mm plate gives 19 mm — 1 mm too much, which closes the gap at the meeting stile and makes the two doors rub.
  • Correct answer: 0 mm plate plus cam adjustment toward the carcass, or K = 4 mm with the 2 mm plate. This is why the boring pattern and the plate height have to be chosen together.

Half overlay: the shared partition

With two doors on one 18 mm partition, each door covers 9 mm. The arithmetic looks simple and usually is, until the partition is not 18 mm.

  • Measure the actual panel, not the nominal. 18 mm board is often 17.4–18.2 mm, and two doors sharing it double the error.
  • Set both hinges from the same batch where possible; a crank difference between batches shows as one door sitting proud.
  • Leave a 2–3 mm gap between the two doors at the meeting point, and check it with the doors loaded — a full-height door sags slightly even with good hinges.

Inset doors: where geometry becomes visible

Inset doors need the hinge to pull the door back into the opening, so the crank and the plate both differ from overlay types. Three rules prevent most inset complaints:

  1. Build the opening to the door size plus the gap, typically 2 mm all round. Do not try to close a 4 mm opening with hinge adjustment.
  2. Use a plate height that matches the door thickness, not the carcass. Inset geometry references the door face.
  3. Test one door before boring forty. Inset errors are cumulative and the whole run has to match.

Soft-close mechanics and the geometry trap

A soft-close hinge adds a damper, and the damper takes up space inside the cup housing. That has two practical consequences for specification:

  • Cup depth is not free. A damped hinge that fits a 13 mm cup bore may not fit an 11.5 mm bore. Confirm the depth against the actual hinge, not the family name.
  • The closing arc is different. The damper engages in the last 15–20 degrees, so a door that is out of alignment by 2 mm closes with a soft bump and a visible gap rather than a hard stop that would show the problem immediately. Soft-close hides geometry errors until a customer notices the uneven reveal weeks later.

For inset doors the effect is stronger: the damper pulls the door slightly toward the carcass at the end of travel, so the gap at the hinge side can differ from the gap at the handle side. Check both edges, not just the one you adjusted.

Mistakes that show up as rubbing doors and uneven gaps

  • Choosing the angle from a catalogue photo. The angle has to clear the wall, the handle and the adjacent door in the actual layout.
  • Mixing plate heights within a run. Two plate heights look identical in a bin and produce a 2 mm step across a run of doors.
  • Boring the cup before confirming the door thickness. A 16 mm door with a 13 mm cup leaves 3 mm of material — enough to show a bulge on the face.
  • Assuming adjustment will fix layout errors. Cams move a door a few millimetres; they do not change the crank.
  • Ignoring the handle in the swing arc. A 165-degree hinge with a 160 mm pull can still hit the neighbouring panel.

What this means for importers in 2026–2027

Hinge specification is moving from “a 110-degree soft-close hinge” to a boring pattern and an overlay table attached to the purchase order. Buyers who send the door thickness, the cup distance and the required reveal get hinges that install without adjustment; buyers who send a photo get a shipment that fits approximately, and a site full of fitters compensating with screwdrivers.

As a factory-sourced supplier of cabinet hardware from China, we work from the boring pattern and the overlay requirement rather than from a product name, and we confirm the plate height and crank before production.

FAQ

What is the difference between full overlay and half overlay?

Full overlay means the door covers the entire carcass edge, so one door closes over one side of the cabinet. Half overlay means two doors share one carcass partition and each covers half of it. The difference is in the hinge crank, so the two are not interchangeable by adjustment.

What cup distance should I specify?

3–5 mm from the door edge to the cup bore is the normal range, with 5 mm the most common for 18 mm doors. The cup distance sets the maximum overlay the hinge can achieve, so it has to be chosen together with the base plate height, not before it.

Do I need a 165-degree hinge?

Only where the door has to swing back past 110 degrees — corner cabinets, doors beside a return wall, or appliances that need the door out of the way. Wider angles need more clearance behind the door, so check the swing arc including the handle before specifying.

Why do my doors rub in the middle?

Usually one of three things: the overlay is 1–2 mm too large for the plate height, the carcass partition is thicker or thinner than assumed, or the two hinges on a pair of doors came from different crank batches. Measure the actual overlay at the meeting stile before adjusting anything.

Can hinge adjustment fix a wrong crank?

No. Cam adjustment moves the door a few millimetres in and out, up and down. It cannot change the crank, so a full-overlay hinge will not work on an inset door no matter how the screws are turned.


Ready to build your 2026–2027 hinge specification?

WFMingKun Hardware supplies cabinet hinges and furniture hardware — 110-degree soft-close, 165-degree, aluminium-frame and heavy-duty hinges — factory-sourced from partner factories in China, with boring patterns, overlay tables, OEM/ODM support and export packing for distributors, importers and furniture makers. MOQ from 500 pcs per item, trial quantities from 50 pcs on most items. Samples in 3–7 working days; bulk production 15–30 days after deposit.

Browse our hinge range or cabinet hardware, or send us your inquiry with your door thickness, cup distance and required overlay — you will get prices, MOQ and lead time within 24 hours. Prefer to talk first? Message us on WhatsApp: +86 187 5400 6560.



Scroll to Top